搅拌车中润滑器的作用是将润滑油雾化并注入气流中，进入需要用空气润滑的部位。因此，注油器中的润滑油必须保持在正常位置，既不能过多也不能过偏很少。那么搅拌车油雾器润滑油前后的检查维护相关内容是什么呢？
The function of the lubricator in the mixer truck is to atomize the lubricating oil and inject it into the air flow into the parts that need to be lubricated with air. Therefore, the lubricating oil in the oiler must be kept in the normal position, neither too much nor too little. So what is the relevant content of inspection and maintenance before and after the lubricating oil of the oil atomizer of the mixer truck?
1、操作前检查项目
1. Inspection items before operation
全自动搅拌车空气系统运行前检查润滑油油位，保持油位在油尺上下线之间，接近下限时及时提高油位线。,油杯口密封圈完好。
Before the operation of the air system of the full-automatic mixer truck, check the lubricating oil level, keep the oil level between the upper and lower lines of the dipstick, and raise the oil level line in time when it is close to the lower limit., The sealing ring at the mouth of the oil cup is intact.
2、添加润滑油的注意事项
2. Precautions for adding lubricating oil
①加油时，应无压力进行。作业前应将搅拌车周围的灰尘等杂物清理干净，以免进入注油器。
① When refueling, there should be no pressure. Before operation, dust and other sundries around the mixer shall be cleaned to avoid entering the oiler.
②注油器内的润滑油为普通柴油机油，可使用粘度为2.5-7度的润滑油或工业40#油。储油杯中的油应及时更换。储油杯容量以100ml计算，使用100小时为宜。
② The lubricating oil in the oiler is ordinary diesel engine oil, and lubricating oil with viscosity of 2.5-7 degrees or industrial 40# oil can be used. The oil in the oil cup should be replaced in time. The capacity of the oil storage cup is calculated as 100ml, and it is appropriate to use it for 100 hours.
3.维护
3. Maintenance
定期清洗空气搅拌车的滤芯。由于滤芯太脏，进入压缩机气缸的空气中含有过多的灰尘，会加速气缸和活塞环的磨损，容易形成积碳，影响气阀的密封性能；会造成拉缸和窜气，造成润滑油污染，影响润滑效果；当气体被窜气时，也会出现油污现象。如果气缸壁与活塞环之间的间隙过大，受污染的润滑油就会进入压缩室。并形成油雾，污染压缩空气。
Clean the filter element of the air mixer regularly. Because the filter element is too dirty, the air entering the compressor cylinder contains too much dust, which will accelerate the wear of the cylinder and piston ring, easy to form carbon deposition, and affect the sealing performance of the air valve; It will cause cylinder pulling and gas channeling, cause lubricating oil pollution, and affect the lubrication effect; When the gas is channeled, oil pollution will also appear. If the gap between the cylinder wall and the piston ring is too large, the contaminated lubricating oil will enter the compression chamber. And form oil mist, polluting the compressed air.
4.清洗
4. Cleaning
定期进行保养规程所规定项目的维护、保养作业，如清洗、润滑、加油等
Regularly carry out the maintenance of the items specified in the maintenance procedures, such as cleaning, lubrication, refueling, etc
搅拌车开动前要先检查各控制器是否良好，停工后用水和石子倒入搅拌筒内10~15分钟进行清洗，再将水和石子清出。操作人员如须进入搅拌筒内清洗时，除切断电源和卸下熔断器外，并须锁好开关箱。
Before starting the mixer, check whether each controller is in good condition. After shutdown, pour water and stones into the mixing drum for 10-15 minutes for cleaning, and then remove the water and stones. If the operator needs to enter the mixing drum for cleaning, he must not only cut off the power supply and remove the fuse, but also lock the switch box.
禁止用大锤敲打的方法积存在搅拌车筒内的混凝土，只能用凿子。
It is forbidden to use a sledgehammer to remove the concrete accumulated in the mixer drum, and only a chisel can be used to remove it.
在严寒季节，全自动搅拌车工作完毕后应用水清洗搅拌机滚筒并将水泵、水箱、水管内积水放净，以免水泵、水箱、水管等冻坏。
In the severe cold season, after the work of the full-automatic mixer truck is completed, the mixer drum shall be cleaned with water and the accumulated water in the water pump, water tank and water pipe shall be drained to avoid freezing damage of the water pump, water tank and water pipe.
想要延长搅拌车的使用寿命，一定要严格按照正确的方法操作！
If you want to prolong the service life of the mixer truck, you must operate in strict accordance with the correct method!
以上就是问题解答的相关内容了，希望能够帮助到大家，如对这一问题还存在任何疑问，都欢迎关注我们网站http://www.zkzdsljbc.com并咨询我们的工作人员，将竭诚为您服务。
The above is the relevant content of the question answer. I hope it can help you. If you still have any questions about this problem, you are welcome to follow our website http://www.zkzdsljbc.com And consult our staff, will serve you wholeheartedly.
