如果作业完成，那么小型混凝土搅拌车就会在库里闲置，这个时候很多人会觉得都闲置了肯定不会出现什么问题，然而并不是，小型混凝土搅拌车闲置时要预防生锈和变形！
If the operation is completed, the small concrete mixer will be idle in the warehouse. At this time, many people will feel that there will be no problem if it is idle. However, it is not. Rust and deformation should be prevented when the small concrete mixer is idle!
小型混凝土搅拌车运行后，须外部污垢，清洗工作机构内的饲料和杂物，要时用水或油清洗，所有润滑部位须清洗干净并重新润滑。清洁搅拌机后，操作人员还应在搅拌机上涂抹油或贴纸，以减少与空气接触的设备氧化的机会。我建议将搅拌机放在凉爽、干燥、通风的房间内。
After the operation of the small concrete mixer truck, it is necessary to remove the external dirt, clean the feed and debris in the working mechanism, and clean with water or oil when necessary. All lubricating parts must be cleaned and re-lubricated. After cleaning the mixer, the operator should also apply oil or stickers on the mixer to reduce the chance of oxidation of equipment in contact with air. I suggest placing the mixer in a cool, dry and ventilated room.
复杂精密的设备应放置在室内阴凉、干燥、通风的地方。简单的设备可以露天存放，但应放在高处、干燥、无阳光直射的地方。它可以覆盖一个棚子和所有与地面直接接触的部分。用木板或砖块支撑，重新刷掉掉下来的保护漆。
Complex and precise equipment should be placed indoors in a cool, dry and ventilated place. Simple equipment can be stored in the open air, but should be placed in a high, dry place without direct sunlight. It can cover a shed and all parts in direct contact with the ground. Support with wood or brick, and brush the fallen protective paint again.
小型混凝土搅拌车的弹簧。传动带。长柄。由于长期受力或放置不合理，零部件会发生塑性变形，因此在搅拌机框架下应增加适当的支撑点，以减少搅拌机负荷。此外，轮胎、播种管等拆下的零配件应妥善保管，防止挤压变形。
Spring of small concrete mixer. Drive belt. Long handle. Due to long-term stress or unreasonable placement, plastic deformation of parts will occur, so appropriate support points should be added under the mixer frame to reduce the load of the mixer. In addition, the removed spare parts such as tires and seeding pipes should be properly kept to prevent extrusion deformation.
对于长期停放的小型混凝土搅拌车，应建立登记卡，详细记录机器和工具的技术状况、附件、备件和工具。如果没有仓库，当机器停放在室外时，应将电机、传动带等易丢失的部件取出，标记并存放在室内。
For small concrete mixer trucks parked for a long time, a registration card shall be established to record the technical conditions, accessories, spare parts and tools of the machines and tools in detail. If there is no warehouse, when the machine is parked outdoors, take out the motor, drive belt and other parts that are easily lost, mark and store them indoors.
如果再次使用的话，就要做好开机前的准备工作，比如：检查传动离合器和制动器是否灵活可靠，钢丝绳是否损坏，履带轮是否完好，周围是否有障碍物及各部位润滑情况等。
If it is used again, it is necessary to make preparations before starting up, such as checking whether the transmission clutch and brake are flexible and reliable, whether the wire rope is damaged, whether the track wheel is in good condition, whether there are obstacles around and the lubrication of all parts.
开机后，要时刻注意搅拌机各部分运转是否正常。停机时要经常检查搅拌机的叶片是否弯曲，螺丝是否被敲落或松动。更多搅拌车使用事项就来我们网站http://www.zkzdsljbc.com咨询了解吧！
After starting, always pay attention to whether all parts of the mixer operate normally. Always check whether the blades of the mixer are bent and whether the screws are knocked off or loose when the machine is stopped. Come to our website for more information about the use of mixer trucks http://www.zkzdsljbc.com Ask about it!
