混凝土搅拌车是一种特别车辆，并不是所有会开车的司机都会开搅拌车，如果操作不当或许会引起不必要的麻烦，所以接下来 的文章主要讲一下在工作中需要注意的细节问题。
The concrete mixer truck is a special kind of vehicle. Not all drivers who can drive the mixer truck can drive it. If it is operated improperly, it may cause unnecessary trouble. So the next article will mainly talk about the details that need attention in work.
1、起动搅拌车之前，应把搅拌筒操作手柄放在“中止”方位。
1. Before starting the mixing truck, put the operating handle of the mixing drum in the "stop" position.
2、起动发动机后，应使搅拌筒在低速下滚动10分钟左右，使液压油温度升到20℃以上方可作业。
2. After starting the engine, the mixing drum should be rolled at low speed for about 10 minutes to make the hydraulic oil temperature rise to above 20 ℃ for operation.
3、搅拌车在露天停放时，装料前应将搅拌筒回转，将积水和杂物排出，以确保后期使用时混凝土的质量。
3. When the mixing truck is parked in the open air, the mixing drum shall be rotated before loading to drain the accumulated water and sundries, so as to ensure the quality of concrete in later use.
4、搅拌车在运输混凝土时，要确保滑斗放置牢固，避免因松动造成摆动，在跋涉中打伤行人或影响其它车辆正常运转。
4. When transporting concrete, the mixer truck shall ensure that the sliding bucket is firmly placed to avoid swinging due to looseness, hurting pedestrians or affecting the normal operation of other vehicles.
5、搅拌车装运搅拌好的混凝土时，搅拌筒转速为2-10转/分；在运输过程中，平坦路面上搅拌筒转速坚持2-3转/分；行驶在侧 倾坡度大于50的路面，或左右晃动较大的路面时，应中止搅拌旋转，待路况 好转后再恢复搅拌旋转。
5. When the mixing truck is transporting the mixed concrete, the mixing drum speed is 2-10 rpm; During transportation, the speed of mixing drum shall be 2-3 rpm on the flat road; When driving on a road with a side slope greater than 50, or on a road with large left and right shaking, the mixing rotation shall be stopped, and the mixing rotation shall be resumed after the road conditions improve.
6、搅拌车在排出混凝土之前，应使搅拌筒在10-12转/分的转速下滚动1分钟，再进行排料。
6. Before discharging concrete from the mixer truck, the mixing drum shall be rolled at 10-12 rpm for 1 minute before discharging.
混凝土搅拌车出料结束，应立即用随车的软管放水将进料口、出料斗及出料溜槽等部位冲刷洁净，排去粘结在车身遍地的污 物及残留混凝土，再向搅拌筒内注水150-200L的清水，在返回途中要让搅拌 筒慢速滚动，以清洗内壁，避免残余料渣附在筒壁 和搅拌叶上，并在再一次装料前将废水排掉。更多相关内容就来我们网站http://www.zkzdsljbc.com咨询吧！
After the discharge of the concrete mixer truck, immediately use the hose attached to the truck to wash the inlet, discharge hopper, discharge chute and other parts clean, drain the dirt and residual concrete stuck on the vehicle body, and then fill the mixing drum with 150-200L of water. On the way back, let the mixing drum roll slowly to clean the inner wall, avoid the residual material slag attached to the drum wall and mixing blade, and drain the waste water before loading again. Come to our website for more relevant content http://www.zkzdsljbc.com Ask!
