搅拌车车主在驾驶期间时常会遇到问题，比如说离合器踏板已踩到底，但挂挡很困难，勉强挂上挡后，尚未放松离合器踏板，全自动搅拌车已行驶或熄火。那么全自动搅拌车离合器挂档不好怎么找原因？
Mixer car owners often encounter problems during driving, such as the clutch pedal has been stepped to the bottom, but it is difficult to hang up the gear, barely hanging up the clutch pedal, the automatic mixer has been running or flameout. So how to find the reason why the clutch of automatic mixer is not good?
将离合器底盖拆下，把变速器挂入空挡，离合器踩到底。然后，用起工具拨动从动盘。如能轻松拨转，说明离合器分离良好；如拨不动，说明离合器分离不彻底。并检查全自动搅拌车离合器踏板自由行程是否过大，并调整。
Remove the clutch bottom cover, put the transmission into neutral, and press the clutch to the bottom. Then, use the pick tool to turn the slave plate. If you can easily turn, that the clutch separation is good; If not, the clutch separation is not complete. And check the automatic mixer clutch pedal free travel is too large, and adjust.
检查全自动搅拌车分离杠杆高度是否一致、是否过低。在车下拨动分离拨叉，使全自动搅拌车分离轴承前端靠在分离杠杆内端面上，转动离合器一周进行查看，如果分离杠杆的内端能同时和分离轴承接触不上，说明分离杠杆的高度不一致，需应进行调整。
Check whether the height of separation lever of automatic mixer is consistent and too low. Under the car dial the separation fork, so that the front end of the automatic mixing truck separation bearing is on the inner end of the separation lever, turn the clutch for a week to check, if the inner end of the separation lever can not contact with the separation bearing at the same time, the height of the separation lever is inconsistent, and it should be adjusted.
如果分离杠杆高度一致，仍然分离不彻底，就要检查杠杆高度。将各分离杠杆调到同样的高度，如果能彻底分离，说明原来调整不当或是磨损过甚。分离杠杆调整之后，须重新调整离合器踏板的自由行程。
If the separation lever height is consistent and the separation is still incomplete, check the lever height. The separation lever is adjusted to the same height, if it can be completely separated, the original adjustment is improper or wear too much. After the separation lever adjustment, the free travel of the clutch pedal must be readjured.
如果上述调整正常后，仍然分离不彻底，就要拆下全自动搅拌车离合器，检查从动盘是否装反、轴向移动是否困难、主从动盘有无翘曲、分离杠杆螺钉是否松动、浮动销是否脱落。
If the above adjustment is normal, the separation is still not complete, it is necessary to remove the automatic mixing car clutch, check whether the driven plate is installed, whether it is difficult to move in the axial direction, whether the main and slave moving plate is warping, whether the separation lever screw is loose, whether the floating pin falls off.
对于全自动搅拌车的离合器，除上述检查外，还应检查制动液是否缺少，管道是否渗漏并排出液压系统内的空气。更多内容的了解您可以来网站www.zkzdsljbc.com看看相关资讯！
For the clutch of automatic mixer, in addition to the above inspection, should also check whether the brake fluid is missing, whether the pipeline leakage and discharge of air in the hydraulic system. For more information, you can come to www.zkzdsljbc.com!
