全自动搅拌车轴承损坏了怎么处理？全自动搅拌车滑动轴承早期损坏比轴承烧毁要常见得多，因此预防滑动轴承早期损坏很重要。下面小编为您讲解更为详细的内容。
How to deal with the damaged bearings of the automatic mixer? The early damage of the sliding bearing of the automatic mixer is much more common than the bearing burning, so it is important to prevent the early damage of the sliding bearing. The following sections will explain more details for you.
滑动轴承的正确维护是减少轴承早期损坏的有效途径，也是延长轴承寿命的可靠保证。因此，在发动机的日常维护和维修中，须注意轴承的合金表面、背面、端头及边缘棱角处的外观形状，
The correct maintenance of sliding bearing is an effective way to reduce the early damage of bearing, and also a reliable guarantee to extend the service life of bearing. Therefore, in the daily maintenance and repair of the engine, attention must be paid to the appearance of the alloy surface, back, end and edge corners of the bearing,
如有异常或出现过半磨损的征兆，就要认真查明原因，并采取相应的措施，改善轴承的工作条件，重视对滑动轴承早期损坏的预防。
In case of any abnormality or signs of more than half wear, it is necessary to carefully find out the causes, take corresponding measures, improve the working conditions of bearings, and pay attention to the prevention of early damage of sliding bearings.
滑动轴承在气缸压力冲击载荷的反复作用下，表面层发生塑性变形和冷作硬化，局部丧失变形能力，逐步形成条纹并不断扩展，然后随着磨屑的脱落，在受载表面层形成凹穴。一般轴瓦发生穴蚀时，是先出现凹坑。
Under the repeated action of the cylinder pressure impact load, the surface layer of the sliding bearing undergoes plastic deformation and cold work hardening, loses the deformation ability locally, gradually forms stripes and continues to expand, and then forms cavities on the loaded surface layer as the wear debris falls off. In general, when cavitation occurs on the bearing bush, the pit appears first.
然后这种凹坑逐步扩大并引起合金层界面的开裂，裂纹沿着界面的平行方向扩展，直到剥落为止。
Then the pits gradually expand and cause the alloy layer interface to crack, and the cracks extend along the parallel direction of the interface until peeling off.
滑动轴承穴蚀的主要原因是，由于油槽和油孔等结构要素的横断面突然改变引起油流强烈紊乱，在油流紊乱的真空区形成气泡，随后由于压力升高，气泡溃灭而产生穴蚀。
The main reason for cavitation of sliding bearing is that the sudden change of cross section of structural elements such as oil groove and oil hole causes a strong disorder of oil flow, forming bubbles in the vacuum area where the oil flow is disordered, and then cavitation occurs due to bubble collapse due to pressure rise.
全自动搅拌车轴承损坏了怎么处理？以上就是问题的相关解答了，所以说要求你在平日使用中多检查固定维护保养，延长其寿命不是问题。关注我们http://www.zkzdsljbc.com，了解更多问题！
How to deal with the damaged bearings of the automatic mixer? The above is the relevant answer to the question, so you are required to check and maintain the fixed parts more frequently in daily use, so it is not a problem to extend their service life. Follow us http://www.zkzdsljbc.com , learn more!
