The engine of the automatic concrete loading mixer is the core engine of the mixer, and is the core component of whether the automatic concrete loading mixer can work smoothly. During the operation of the automatic concrete loading mixer, the high water temperature of the engine of the automatic concrete loading mixer is a frequent occurrence. Then, what should be done when the water temperature of the engine of the automatic concrete loading mixer is too high? The answers are as follows:
，打开发动机罩盖，让发动机怠速运转，等待发动机温度逐渐恢复正常。在发动机水温恢复正常之后，将发动机熄火，然后再等待一段时间，直到发动机的水温充分地下降了之后，再检查发动机的冷却水量。
First, open the engine cover, let the engine idle, and wait for the engine temperature to gradually return to normal. After the water temperature of the engine returns to normal, turn off the engine, and then wait for a period of time until the water temperature of the engine drops sufficiently, and then check the cooling water volume of the engine.
其次，如果混凝土自动上料搅拌车在普通公路上发动机出现了过热，应该尽快地降低车速，把汽车驶到树荫下，或驶到相对比较凉快的地方，把汽车停下来，但这时候不要急于熄火。
Secondly, if the engine of the concrete automatic loading mixer is overheated on the ordinary road, the vehicle speed should be reduced as soon as possible, and the vehicle should be driven to the shade, or to a relatively cool place, and the vehicle should be stopped, but at this time, do not be in a hurry to stop the fire.
另外，另外，如果发现混凝土自动上料搅拌车发动机发热现象，此时发动机的冷却水量可能大都严重不足。按着规定量把冷却水补足之后，再检查一下冷却系统，确认没有其他故障之后，可以起动发动机，继续行驶。也要检查一下水箱百叶窗是不是被异物堵塞，风扇叶的工作情况，发动机皮带是否打滑，发动机水泵工作情况等。
In addition, if the engine of the automatic concrete loading mixer is found to be hot, the cooling water of the engine may be mostly insufficient. After replenishing the cooling water according to the specified amount, check the cooling system again. After confirming that there are no other faults, start the engine and continue driving. Also check whether the water tank louver is blocked by foreign matters, the working condition of the fan blade, whether the engine belt slips, the working condition of the engine water pump, etc.
，混凝土自动上料搅拌车如果在高速公路上出现了发动机过热，要立刻把暖风全部打开并打开车窗，由于有暖风帮助冷却水散热，能使冷却水温大幅度地下降。这样可以让您持续开车，就近找到高速公路的出口，将搅拌车驶到的场所停下来。接下来，只要按照上述的方法，使发动机的温度降下来就行。注意，不要把搅拌车停在路边，以免影响交通或被撞车，必须把搅拌车停在的场所。
In the end, the engine overheated on the highway. You have to open all the warm air and open the windows immediately. Then the car will be as hot as hell. Because there is warm air to help cooling water dissipate heat, the cooling water temperature can be greatly reduced. In this way, you can drive continuously, find the exit of the highway nearby, and drive the mixer to a safe place to stop. Next, just follow the above method to lower the engine temperature. Note that it is better not to park the mixer on the side of the road, so as not to affect the traffic or be hit. The mixer must be parked in a safe place.
以上是中科聚峰混凝土自动上料搅拌车发动机水温过高的处理方法，希望今天小编的介绍能对大家有所帮助，以后使用时能更加得心顺手。
The above is the treatment method for the excessive water temperature of the engine of Zhongke Jufeng concrete automatic loading mixer. I hope today's introduction of Xiaobian can help you and make you more comfortable when you use it in the future.
