When we check the concrete mixing plant regularly, we need to check the steel wire rope first. Put a little butter on it for a week to ensure adequate operation. If the steel wire rope is seriously worn, it shall be replaced in time. Check the grease level of the heavy oil pump and replace the grease if necessary. In addition, the water supply system of the concrete mixing plant shall be kept clean at all times to avoid blockage. The suction valve shall be inspected and cleaned regularly.
每个电机和电气组件的接线不得松动，并且应检查交流接触器的接触器。 混凝土搅拌站配电箱中的灰尘应清理干净，限位开关不得进入水中。 经常检查设备，可以随时发现设备的使用故障，应及时对混凝土搅拌站进行维修和修理，以延长其使用寿命。
The wiring of each motor and electrical component shall not be loose, and the contactor of AC contactor shall be checked. The dust in the distribution box of the concrete mixing plant shall be cleaned, and the limit switch shall not enter the water. Check the equipment frequently, and the use failure of the equipment can be found at any time. The concrete mixing plant shall be repaired and repaired in time to prolong its service life.
，气体控制系统可以实现便捷的输入，便捷的操作，并且可以准确地调整和修改每种物料的设定值; 电气控制系统须具有完善的自锁和互锁功能，以确保系统准确，可靠地运行。 常见的故障电气控制系统须具有故障检测和报警功能。 使用混凝土搅拌
Firstly, the gas control system can realize convenient input and convenient operation, and can accurately adjust and modify the set value of each material; The electrical control system must have perfect self-locking and interlocking functions to ensure the accurate and reliable operation of the system. The common fault electrical control system must have the function of fault detection and alarm. Mixing with concrete
其次，该空气控制系统在混凝土搅拌站的配料过程中输出为零，从而地控制了计量精度的功能，并设有光报警装置。 有些用户甚不知道空气控制系统的一部分，这并不重要。 实际上，空气控制系统就是要实现整套设备的自动化。 没有空气控制系统的混凝土搅拌站设备不能正常运行，其重要性很高。
Secondly, the output of the air control system is zero in the batching process of the concrete mixing plant, so as to effectively control the function of measurement accuracy, and a light alarm device is set. Some users don't even know part of the air control system, which is not important. In fact, the air control system is to realize the automation of the whole set of equipment. The equipment of concrete mixing plant without air control system can not operate normally, which is of high importance.
空气控制系统在混凝土搅拌站中的重要性不言而喻。
The importance of air control system in concrete mixing plant is self-evident.
实际上，整个混凝土搅拌站的搅拌系统，骨料系统，输送系统，气体控制系统和控制系统都是重要和必不可少的。 混凝土搅拌站生产线中的中间搅拌仓主要是由于骨料的混合效率有时高于粉末和水的混合效率，因此过渡室用于等待粉末和水的配料工作。 常见于大型搅拌站。
In fact, the mixing system, aggregate system, conveying system, gas control system and control system of the whole concrete mixing plant are important and essential. The intermediate mixing bin in the production line of concrete mixing plant is mainly because the mixing efficiency of aggregate is sometimes higher than that of powder and water, so the transition chamber is used to wait for the mixing of powder and water. Common in large mixing plants.
如果小型搅拌站使用料斗升降机，则实际上没有中间皮带仓，骨料可以在提升的料斗中等待。 同时，由于骨料沉重而容易忘记的部分将沉入底部。 此时，如果加入骨料，则不利于混凝土的均匀混合。 它将延长混合周期并降低混合效率。 此时，将粉末放入水中。 实际上，与骨料混合并搅拌，提高混合效率是有益的。
If a hopper elevator is used in a small mixing plant, there is actually no intermediate belt bin, and the aggregate can wait in the lifted hopper. At the same time, the easily forgotten part due to the heavy aggregate will sink to the bottom. At this time, if aggregate is added first, it is not conducive to the uniform mixing of concrete. It will extend the mixing cycle and reduce the mixing efficiency. At this time, first put the powder into water. In fact, it is beneficial to mix and mix with aggregate to improve mixing efficiency.
如果需要维护，则电动机要连续运行，并且日常维护非常重要：电动机在工作时，请注意工作环境，不要太颠簸，以防止电动机损坏或减速。 使用寿命。 还要检查外观，风扇是否正常工作，是否异常振动，联轴器是否可靠，基座是否定期固定，轴承是否正常工作(听声音)以及温度是否正常( 红外温度计))，电流是否正常(钳型电流表)，并且缠绕的电动机还须检查碳刷和滑环。 如果一方面存在异常，则需要快速进行电机维修和处理。 否则，情况严重后，您将无法处理。。
The motor shall not be damaged during daily operation or continuous maintenance. If it is necessary to slow down the motor, please pay attention to prevent the motor from being damaged. service life. Also check the appearance, whether the fan works normally, whether it vibrates abnormally, whether the coupling is reliable, whether the base is fixed regularly, whether the bearing works normally (listen to the sound) and whether the temperature is normal (infrared thermometer)), whether the current is normal (clamp on ammeter), and check the carbon brush and slip ring of the wound motor. If there are abnormalities on the one hand, the motor needs to be repaired and handled quickly. Otherwise, when the situation is serious, you will not be able to handle it..
